The House That Math Built

Maxine Edwards and Mary Teal
The Center for Advancement of Teaching

---

The House That Math Built
Lesson Plan
Algebra 1 Level

Explore: Complete the activity of transferring the picture to the CFX-9850.

Equipment
2 Motion Detectors
2 EA-100s
CFX-9850G
1 picture of " The House That Math Built"
meter sticks - for measuring and pointing
tape
data communication cable


1. Perform experiment as follows:
   • Tape the picture of "The House That Math Built" to a LARGE table.
   • Set up TWO EA-100 devices with a Motion Detector attached to each one.
   • Place the motion detectors on the table top as indicated on the picture. Be sure to measure accurately and position the detectors so that the cones of detection are perpendicular to each other. The intersection of the cones must be located over the center of the picture.
   • Make sure the motion detector is plugged into the SONIC port of the EA-100. DO NOT connect the EA-100 to the calculator.
   • To collect data points, use a meter stick held over the picture to point to each vertex in the order specified. Note: It is EXTREMELY IMPORTANT that the pointer operator is not inside the cones of detection. This may mean that the student must stand on a chair.
   • Listen to the ticking sounds emitted from the motion detectors. After pointing to a vertex and hearing the corresponding tick of the detector, move the stick to the next point. Wait for the tick before continuing in like manner. After reaching the final point, wait at that vertex until the EA-100s says DONE.
   • To operate the EA-100 manually, use the following keystrokes:

     KEYSTROKE 	EXPLANATION
     a.  Press[SHIFT][MODE]	"Set-up"
           b.  Press [DATALOG] until "5 Sec" appears	"Next"  Press [DATALOG] several
     	times until the sample time you want
     	appears (5 Sec)
     c.  Press[TRIGGER]	Chooses the 5 Sec as the time
     d.  Press[DATALOG] until "10" appears	Press [DATALOG] several times until 
     	the number of sample points you want 
     	appears (10)
     e.   Press[TRIGGER]	Chooses 10 as the number of samples
     f.    Press [DATALOG] until 1 appears	"Next" Press [DATALOG] until you see 
     	the time consideration you want.  In this
     	case, the time will be collected as data.
     g.   Press[TRIGGER]	Selects time consideration.
     h. Press[TRIGGER]	Begins sampling.  This means that it is 	time to place the pointer on each 
     	individual letter on the picture in the 
     	following order : A C B D E C D A B
     
     

2. Retrieve the data from the EA-100:
   c. Connect EA-100 to CFX-9850G using data communication cable.
   d. Turn on CFX-9850G and choose Run (1) from the menu.
   e. Press SHIFT VARS {PRGM}
   f. Press F6 (>) , then I/O {F4}
   g. Press Recu (F4) {Receive( }
   h. Press OPTN, List {F1}, List {F1} ,1, close Parenthesis { ) }
   i. Press SHIFT EXE {¿ }
   j. Press Recu (F4) {Receive( }
   k. Press OPTN, List {F1}, List {F1} ,2, close Parenthesis { ) }
   l. Press EXE
   
   
3. The data should now be listed in List 1 and List 2.
   
   
4. . Go to the Main Menu and choose List (4)
   o. Cursor across the top of the screen, highlighting List 3
   p. Press OPTN , List {F1}, List {F1}, 1 , EXE This will copy the data in List 1 to List 3.
   q. Cursor across the top of the screen, highlighting List 4 r. Press OPTN , List {F1}, List {F1}, 2 , EXE This will copy the data in List 2 to List 4.
   
   
5. Repeat Step 2- ONLY. This will enter the data from the second EA-100 to List 1 and List 2.
   
   
6. For the next part of the procedure you will be operating in the STAT menu.
   s. After entering the STAT menu, you should find List 1 through List 4. Press GRAPH {F1}
   t t. Press SEL {F4}
   u. StatGraph 1 : DrawOn
   v. EXIT
   w. Press SET {F6}
   Graph Type: xyline
   Xlist : List 2
   Ylist : List 4
   Frequency : 1
   Mark Type : ×
   Graph Color: CHOICE
   f. EXIT
   g. GRPH 1 {F1}